How Do I Get My 3ds Camera to Work Again
Repair guide : Cameras Nintendo 3DS
Level : Medium Fourth dimension : xxx min Writer : Alexandre
100 people have done this repair successfully ! Why not you?
This guide is for replacing the power push on the Nintendo 3DS. .
Issues: defective cameras, autofocus, 3D.
Some advice before you first
Recommended repair kit
Step 1
Before disassembling the rear case of your Nintendo 3DS, yous have to make sure the device is turned off.
With a cruciform screwdriver, remove the 4 screws (circled in red) located on the top part of the rear case of the 3DS.
Step 2
Concord the device in one hand and flip the 3DS over so you can slightly open up the rear case. Catch the top border of the back cover with your contrary hand so that the cover does non fall back into place.
Flip the 3DS over over again so that the dorsum embrace is facing up.
Pull the back comprehend up and abroad from the remainder of the device to remove it.
Step iii
Insert the nylon spudger betwixt the bombardment and the lower case of the Nintendo 3DS.
And then pry on the peak role of the battery to remove it.
Step 4
Remove the cruciform screw that secure the lower case :
ix cruciform screws circled in red,
i cruciform screw circled in orange above the game cartridge slot.
The cruciform screws securing the Nintendo 3DS case can be very tighten. Don't hesitate to use a bit of force but careful not to impairment the screws.
Pace 5
Lift the bottom edge of the lower case off the remainder of the 3DS.
There are still 2 ribbon cables connecting the mother board to the case, so be certain not to pull the lower case all the way off.
Step 6
Use the nylon spudger and gently disconnect the L and R button cable from the logic board.
Once the cable are asunder, you can remove the lower example from the Nintendo 3DS .
Step vii
With a nylon spudger, gently pry to disconnect the IR board from the logic board.
Footstep 8
Remove the two cruciform screws circled in red that secure the dorsum of the circle pad to the logic lath.
Step ix
With a nylon spudger, gently remove the back of the circle pad from the logic board.
In one case removed, lay it on its dorsum so that the ribbon cablevision connector is accessible..
Pace 10
Use the flat end of a spudger or your fingernail to flip up the retaining flap on the Circumvolve Pad ribbon cablevision ZIF socket.
Conscientious to pry up on the hinged retaining flap, non the socket itself.
Step 11
Elevator the Circle Pad joystick off the logic board.
Step 12
Utilize the flat terminate of a spudger to pry the SD board ribbon cable connector off its socket on the motherboard..
Step 13
Utilise the cruciform screwdriver and remove the two screws securing the SD bill of fare to the logic board.
Stride 14
The SD bill of fare reader is glued to the logic board.
Insert the flat cease of a spudger between the SD board and the logic board.
Run the spudger along the sides of the SD lath to free it from the adhesive pad.
In one case completely freed, elevator the SD board straight off the logic lath.
Pace fifteen
Slide the flat cease of a spudger under the corner of the Wi-Fi board, and elevator it away from the motherboard..
Don't remove it but notwithstanding, it is still attached to the logic board.
Equally shown on picture three, gently pry with the spudger to disconnect the WiFi antenna.
Pace xvi
With a pair of tweezers, grasp the microphone ribbon cable near the microphone.
The rubber subclass might still be stuck. Utilize a pair of tweezers to remove it.
Pull the microphone straight up out of the upper example..
Footstep 17
Utilize the flat stop of a spudger or your fingernail to flip up the retaining flap on the speaker assembly ribbon cable ZIF socket.
Pry upwardly on the hinged retaining flap, NOT the socket itself.
At present disconnect the speaker assembly ribbon cable with a pair of tweezers.
Footstep 18
Apply the flat stop of a spudger to flip up the retaining flap on the camera ribbon cable ZIF socket..
Pry on the retaining flap, not the socket.
Don't disconnect the cable just yet.
Step xix
Remove the seven cruciform screwd that secure the logic board to the example :
four cruciform screws circled in red,
two blackness cruciform screws circled in orange,
one cruciform screw circled in blue.
Stride twenty
Lift the logic board assembly and rotate it until it is resting adjacent to the rest of the device..
Step 21
Use the apartment end of a spudger or your fingernail to flip up the retaining flap on the LCD ribbon cable ZIF socket.
Once lifted, you can.
You can now safely remove the logic board.
Careful not to affect the LCD screen while removing the logic lath.
Step 22
Earlier standing with disassembly, use a pair of tweezers to remove the clear plastic diffuser for the wireless notification LED.
The small slice is likely to fall out on its ain, and may be difficult to find if it lands on the floor.
Step 23
Now remove the WiFi antenna as shown on the picture.
This is non necessary is you lot're replacing the front panel. However, the replacement of the upper screen, speakers, cameras, and Wi-Fi antenna require it.
Step 24
Use a hair dryer and estrus upward the edges of the upper display front panel.
It is strongly glued, don't hesitate to estrus it up again .
Step 25
Go along prying the remaining sides of the front panel by sliding the plastic opening tool down each edge.
RAPPEL : if you have to utilise a flake of strength, don't hesitate to heat it up once more.
Pace 26
With all of the sides free, lift the upper display front console off the display bezel.
The upper forepart console is at present disassembled. You can replace it with a new one if needed.
Step 27
Now remove the 6 screwssecuring the rear display bezel to the front display bezel.
Footstep 28
With a pair of tweezers, remove the 2 rubber parts on each side of the LCD edge as shown on the moving picture.
Step 29
The rear example of the 3DS is attached by two clips. Use a nylon spudger to unclip them.
Then y'all tin lift the rear ase of the Nintendo 3DS and remove it.
Step 30
With a pair of tweezers, remove the 3D adjustment switch from the front display bezel.
This step is not necessary for disassembly, but the switch is probable to autumn out on its own. By removing it yourself, you lot reduce the risk of losing information technology.
Step 31
Insert a metal probe into the space higher up the ABXY buttons with the point touching the metal hinge. Push the hinge towards the center of the upper case. This will require a fair amount of force.
Step 32
Separate the top part and bottom part of the Nintendo 3DS.
Yous might demand to use a bit of force. Careful not to bend or break the case of your device.
A few cables get into the promise of your device case. Careful not to damage whatsoever of them.
Step 33
Carefully feed the speaker assembly ribbon cable through the pigsty in the upper brandish bezel. Gently curl the ribbon cables to allow them to fit - the cables are wider than the hole.
Step 34
Remove the cruciform screw securing the right speaker lath to the upper display bezel.
Stride 35
Use the flat end of a spudger or your fingernail to flip upwards the retaining flaps on the parallax barrier ribbon cable ZIF sockets.
Be sure you are prying upwards on the hinged retaining flap, not the socket itself.
Apply a pair of metal tweezers to disconnect the two ribbon cables.
Pace 36
Apply the flat end of a spudger to pry the left and right speakers out of their places in the upper display bezel. Pry the camera status LED out of the upper brandish bezel with the tip of a spudger.
Remove the speaker associates from the residual of the display assembly.
Step 37
Gently roll the upper LCD ribbon cable and camera ribbon cablevision together and insert them into the hinge opening.
Step 38
Apply a nylon spudger to peel off the cameras cablevision
Step 39
Carefully pull the camera and upper LCD ribbon cables through their hole in the upper display bezel.
Recommended repair kit
Source: https://www.sosav.com/guides/game-consoles/nintendo/nintendo-portable/nintendo-3ds/cameras/
Post a Comment for "How Do I Get My 3ds Camera to Work Again"